Belt conveyor operating code

1, all channels, escalators, steps or platforms should have at least 0.5m wide channel, if the conveyor movable parts and fixed obstacles between the width of the channel is less than 0.5m, should be equipped with protective devices.
(2) Platforms, floors or similar structures above 1.5m above the ground shall be provided with fixed channels. The best channel is a slope or ladder with slats, and the Angle between the ladder and the level is not more than 60°, otherwise, the ladder should be equipped with solid handrails.
3, all platforms or channels of the floor and stairs and steps of the tread should be suitable for the working conditions of the conveyor, and there should be anti-skid measures.
4, in the conveyor from the ground 2m height below, personnel can enter and exit the area, should prevent sharp protruding edges. Otherwise, protective measures should be added.
5. If the clearance height under the device is less than 1.9m, it is recommended to use the channel across the device.
6, if the conveyor equipment into the pit or through the floor and there is a hole, should be set up at the hole protection railing and foot baffle.
7, if the conveyor across the workbench or channel above, should be set up appropriate protective devices to prevent the transport of materials accidentally dropped.
8. Protective measures must be taken near the weight tensioning device to prevent personnel from entering the space below the weight.
9, the protective cover should be firmly positioned, and no other parts need to be removed when moving or replacing.
10, all channels, handrail rod, ladder, ladder, fence, etc. should be installed before the conveyor is put into use.
11. Welding is prohibited in the conveyor roadway, and the roadway support of 10m before and after the conveyor head and tail should be supported by non-combustible materials.
12, the conveyor roadway should be laid fire hose, the head, tail and roadway every 50m should be equipped with fire hydrants, and equipped with faucets and adequate fire extinguishers.
13, the conveyor should not be used to complete tasks other than the design requirements, nor should it be used under abnormal working conditions.
14, the user should pay attention to ensure that the conveyor regularly feed, as far as possible to prevent overload. In particular, the user is not allowed to change the position of the loading point or increase its throughput and carry out other changes that affect the performance of the equipment without consulting the design and manufacturing unit, in order to prevent adverse consequences.
15. It is strictly prohibited to take people by conveyor. Conveyors specially designed for passengers shall comply with the special rules for carriers.
16, all the protection devices of the conveyor must be complete, and set up regular inspection and verification, to ensure the reliability of its work.
17, the conveyor and its main components should be carried out according to the manufacturer's instructions to carry out good maintenance, the moving parts and cleaning device to carry out regular inspection, adjustment, maintenance and cleaning, these operations should be carried out after the equipment is stationary and the drive device is closed. All loading points, workstations and passageways shall be kept clean and tidy.
18. The inspection hole is not allowed to open when the conveyor is running.
19, strict conveyor full-time driver responsibility system, often tour to check the operating status of the conveyor, such as abnormal phenomenon should be immediately carried out repair or replacement. In particular, all starting operations must be carried out by personnel who have passed the assessment and hold a job certificate, and other personnel are not allowed to operate or interfere with the normal operation of the equipment.
20, the parking device along the line must let all staff understand its function, the device should be easy to operate, and regularly check.
21. Before the conveyor stops normally, all the materials on the conveyor must be unloaded before the power can be cut off.
22, before the conveyor accident or accident stop and restart, it is necessary to carry out a detailed inspection in advance to find out the cause of the stop and eliminate the fault.
23, it is strictly prohibited to cross the conveyor equipment or pass under the equipment.
24, the conveyor in operation or use of inspection and adjustment operations in the case of equipped with protective devices, except in the case of the protective device is not removed and cannot carry out the operation. If some protective devices have to be removed, necessary precautions should be taken and access to the parts where there is a risk of biting should be strictly prohibited.
25. If the protective parts are located in the work area or aisle, these areas must be surrounded when the equipment is in operation to prevent personnel from approaching.
26, when repairing the protective device, it must be stopped in the conveyor, the drive device can not be started before it can be carried out, and the protective device should be installed before restarting. If repairs have to be carried out on unprotected operating equipment, the person at work must be watched over by a guardian who is familiar with what to do in the event of an accident and who is close to a device that can be stopped at any time.